Parts for the bike can be expensive though and costs can quickly add up, especially if you are buying genuine Yamaha parts. Rear cowl and grab rail has also been modified. Removal Throttle cable Caburetor Disassembly 1. . Many of them have a common idiosyncrasy where the clutch cable which goes over the engine stretches when warm causing a snatchy take off in 1st and 2nd gear.
Disassemble: Kick starter device Disassemble: Crankcase cover right Seal papper pad Locating Note:. The brakes stop me every time and a few times that I've needed to really stomp on the back it's stopped me without throwing me! Charge voltage Connect the induction tachymeter to the wire of the spark plug. If the clearance is too large, replace all the three rings. Roughly 260 miles to a tank. Remove the diaphragm of brake liquid vat. C Fix the wire of left handle bar switch and clutch switch with bands. Unsourced material may be challenged and removed.
Oil change and tune up is the key for higher mileage. The clocks are more modern and the bike feels alot better to ride. I find now that whilst working has become tedious, this is offset significantly by a fun journey at each end of the day. Features like self-start, Alloy rims, alluring speedometer with fuel gauge indicator and an ultra-bright headlight, Yamaha Ybr 125 is worth every penny you spend. Clean Carbon deposit Clean from burning chamber Use round-head scraper Note: Do not use sharp tool for avoiding the damagement of the spark plug thread and air valve seat.
Removal Chain joint clip Press plate of chain Chain Driven chain Inspection of drive chain 1. Very reliable, great handling and cornering, recommend Michelin Pilot Sporty tires or similar for better grip and stability. Install Electric brush spring Electric brush Note:. As with most bikes, pay attention to the front forks as they are expensive to replace around £100 per stanchion, not including anything else and can become pitted quite quickly. . Check: Activating state Make the front fork sliding up and down certain times.
Be careful not to damage the matching surface of crankcase. This bike has been launched for those who want to shift from their 100cc bike to an affordable 125cc bike. It can give off road taste along with some gentle ride. Mount: Crank Shielding hood of crank assembly: 90890-04081 Sleeve of crank assembly 90890-01274 Bolt of crank assembly 90890-01275 Template pipe joint 90890-01378 Note: Keep the connecting rod on dead piont. And sometimes it wont't change gear when I've stopped at traffic lights, but rolling it slightly or getting into the right one before hand gets around this. . Replace bulb or socket 2.
. Resistance value of ignition coil Ω ± ° 3. Removal Adjusting nut Tension rod Spring Brake pull rod Rear wheel nut 3. It is a fair bike not pretending to be something else. Disassemble Guide board of chain Locating pin Cylinder pad Cylinder 12.
Most of the riding community already knew that the next model would be the 125G, the trail version and thanks to the internet we already knew what the upcoming bike would look like. Ideally I wanted a Honda Varadero 125, but these are incredibly expensive for a 125, so not worth it unless you plan to keep for a long time. Adjustement of fuel level 1. There is no extra light on the 125G and the riders are left to the mercy of the same 12V 35W halogen bulb. It has a powerful headlight for clear vision at night and comes with other standard safety features like saree guard and pass button.
Installation Rear wheel axle F r o n t w h e e l ў. Third title :It is a title of the smallest unit,which is compiled step by step and matched with relevent picture Exploded Diagram In order to u. . Grip of handlebar is very convenient but the best thing on this bike is now the grip your knees get around its fuel tank. Remove Core of air filter Note:. It's strictly a town bike but does its job well. Measure: Inner diameter of piston pin hole b Inner diameter of piston pin hole: 15.